79 lines
2.9 KiB
Plaintext
79 lines
2.9 KiB
Plaintext
|
#jinja2: lstrip_blocks: True
|
||
|
|
{{ ansible_managed | comment }}
|
||
|
|
|
||
|
|
# default zone
|
||
|
|
# The default zone used if an empty zone string is used.
|
||
|
|
# Default: public
|
||
|
|
DefaultZone={{ firewalld_default_zone }}
|
||
|
|
|
||
|
|
# Clean up on exit
|
||
|
|
# If set to no or false the firewall configuration will not get cleaned up
|
||
|
|
# on exit or stop of firewalld
|
||
|
|
# Default: yes
|
||
|
|
CleanupOnExit=yes
|
||
|
|
|
||
|
|
# Lockdown
|
||
|
|
# If set to enabled, firewall changes with the D-Bus interface will be limited
|
||
|
|
# to applications that are listed in the lockdown whitelist.
|
||
|
|
# The lockdown whitelist file is lockdown-whitelist.xml
|
||
|
|
# Default: no
|
||
|
|
Lockdown=no
|
||
|
|
|
||
|
|
# IPv6_rpfilter
|
||
|
|
# Performs a reverse path filter test on a packet for IPv6. If a reply to the
|
||
|
|
# packet would be sent via the same interface that the packet arrived on, the
|
||
|
|
# packet will match and be accepted, otherwise dropped.
|
||
|
|
# The rp_filter for IPv4 is controlled using sysctl.
|
||
|
|
# Note: This feature has a performance impact. See man page FIREWALLD.CONF(5)
|
||
|
|
# for details.
|
||
|
|
# Default: yes
|
||
|
|
IPv6_rpfilter=yes
|
||
|
|
|
||
|
|
# IndividualCalls
|
||
|
|
# Do not use combined -restore calls, but individual calls. This increases the
|
||
|
|
# time that is needed to apply changes and to start the daemon, but is good for
|
||
|
|
# debugging.
|
||
|
|
# Default: no
|
||
|
|
IndividualCalls=no
|
||
|
|
|
||
|
|
# LogDenied
|
||
|
|
# Add logging rules right before reject and drop rules in the INPUT, FORWARD
|
||
|
|
# and OUTPUT chains for the default rules and also final reject and drop rules
|
||
|
|
# in zones. Possible values are: all, unicast, broadcast, multicast and off.
|
||
|
|
# Default: off
|
||
|
|
LogDenied=off
|
||
|
|
|
||
|
|
# FirewallBackend
|
||
|
|
# Selects the firewall backend implementation.
|
||
|
|
# Choices are:
|
||
|
|
# - nftables (default)
|
||
|
|
# - iptables (iptables, ip6tables, ebtables and ipset)
|
||
|
|
FirewallBackend=nftables
|
||
|
|
|
||
|
|
# FlushAllOnReload
|
||
|
|
# Flush all runtime rules on a reload. In previous releases some runtime
|
||
|
|
# configuration was retained during a reload, namely; interface to zone
|
||
|
|
# assignment, and direct rules. This was confusing to users. To get the old
|
||
|
|
# behavior set this to "no".
|
||
|
|
# Default: yes
|
||
|
|
FlushAllOnReload=yes
|
||
|
|
|
||
|
|
# RFC3964_IPv4
|
||
|
|
# As per RFC 3964, filter IPv6 traffic with 6to4 destination addresses that
|
||
|
|
# correspond to IPv4 addresses that should not be routed over the public
|
||
|
|
# internet.
|
||
|
|
# Defaults to "yes".
|
||
|
|
RFC3964_IPv4=yes
|
||
|
|
|
||
|
|
# AllowZoneDrifting
|
||
|
|
# Older versions of firewalld had undocumented behavior known as "zone
|
||
|
|
# drifting". This allowed packets to ingress multiple zones - this is a
|
||
|
|
# violation of zone based firewalls. However, some users rely on this behavior
|
||
|
|
# to have a "catch-all" zone, e.g. the default zone. You can enable this if you
|
||
|
|
# desire such behavior. It's disabled by default for security reasons.
|
||
|
|
# Note: If "yes" packets will only drift from source based zones to interface
|
||
|
|
# based zones (including the default zone). Packets never drift from interface
|
||
|
|
# based zones to other interfaces based zones (including the default zone).
|
||
|
|
# Possible values; "yes", "no". Defaults to "yes".
|
||
|
|
AllowZoneDrifting={{ firewalld_allow_zone_drifting | bool | ternary("yes", "no", "no") }}
|